Buying Guides
How to Size a Beside-the-Press Granulator for Your Press Tonnage
Press tonnage is the first thing people quote and the least useful. Size a granulator from shot weight, reject rate and the screen you actually run, then pick the motor.
Most granulator quotes start with tonnage: "what press is it for?" That number tells you how big the machine is, not how much plastic you need to cut. A 250T press running a 12 g part makes less scrap in a shift than an 80T press running a 180 g housing. Size from the scrap, then check the footprint.
Start from shot weight and reject rate
Every calculation below needs three inputs:
- Shot weight in grams, runner included
- Cycle time in seconds, so you can convert to shots per hour
- Reject rate as a percentage, plus any sprues you always reclaim
The runner is the part people forget. On a thin-wall part the runner can be 40 percent of the shot, and it is the fraction you will grind all day.
Convert to kilograms per hour
Use this once and write the result on the quotation request:
Worked example: a 45 g shot, 28 s cycle, and you recover 30 percent of the shot as runner and rejects.
- Shots per hour = 3600 / 28 = 128
- Material per hour = 128 x 45 g = 5.8 kg/h
- Recovered share = 5.8 x 0.30 = 1.7 kg/h
So the granulator needs to handle under 2 kg/h, not 6. That is a small machine, and it changes the price bracket completely.
Match motor power to throughput, not to tonnage
The relationship between motor power and throughput is not linear, and it depends far more on the material and the screen than on the kW rating. In practice, a small beside-the-press unit in the 1.5 to 2.2 kW class handles a few kilograms per hour of thin-wall PP or PE. Machines in the 100 kW class exist for central reclamation of thick sections and purgings, not for one press. If a supplier quotes you 100 kW for a 1.7 kg/h job, ask what the extra power is cutting.
Screen and chamber size decide real capacity
Two granulators with the same motor can differ by a factor of two in output because of the screen. A larger hole passes material faster and reduces recirculation inside the chamber. A smaller hole gives you finer regrind and more fines.
Decide the screen from what happens to the regrind next:
- Feeding straight back at the machine: 6 to 8 mm is common, because the regrind must melt in the same cycle
- Bagging for later use: 8 to 10 mm gives a more forgiving, faster-cutting setup
- Fines-sensitive materials or dusty regrind: start finer, then check the dust load before committing
Chamber width matters as much as hole size. Wide, flat runners need a chamber that accepts them without pre-cutting, otherwise you spend the shift feeding material in by hand.
Where the machine sits
A beside-the-press unit is only beside-the-press if the operator can reach it without leaving the cell. Check:
- Height of the feed hopper against the operator's reach and the granulate bin below
- Castors and footprint, if the cell is tight
- Noise level, since a granulator next to an operator is a noise source all shift
- Whether the discharge bin can be lifted out without moving the machine
If one granulator has to serve several presses, the layout problem changes: you need a central unit with ducting or a cart system, and the sizing above has to be summed across the presses that run at the same time.
Checklist before you order
- Shot weight, cycle time and reject rate written down
- Calculated kg/h, with the arithmetic shown
- Screen size chosen against the next process step, not by habit
- Feed opening measured against your largest runner
- Voltage and phase confirmed at the wall
- Bin capacity matched to how often someone is willing to empty it
If you send those six items with an enquiry, any supplier can quote a machine that fits. Without them, the quote is a guess dressed up as a specification.
Browse beside-the-press granulators or send the six inputs through the contact form and we will size it with you.